Nice looking ride! I just checked the Brat map and there are 3 Tomcat owners in your area but not the same model (they have the Tomcat 24 - pretty different boat compared to the 255).
When I was purchasing my boat (Long Island NY) I made the awful 8 hour RT drive three times (ugh).
You can hire a surveyor, but we can help you with a very detailed checklist for review. I compiled mine from other Brat's and it was extremely helpful.
Somethings to get you started:
I put together a general article that some have found helpful here:
http://www.commercialcaptains.com/marine_articles
Choose the link for "Pre-purchase inspection of brand new boats". Bob Austin was gracious enough to put together a great resource for installations once you get to that point as well.
In terms of Tomcat specific things to look for...
1.) Check for telltale stress cracks where cabin mates with the cockpit at the gunwales (right near fuel tank cap).
2.) Look under the cabin roof overhang, typically this area is not properly sealed; you will be able to see if they caulked all the way around with a quick look. It will be easy for them to seal that up.
3.) Shower sump - very common to find these broken or not working. It's very important to test the complete water system by the way - get a fresh water hose and shore power to test the hot water heater, sink, shower, shower sump, toilet flush, etc. It will take a good 30 minutes before you have hot water. Hot water heater only runs off shore power. You will also need juice from your starboard battery selector switch (put on positon 1, 2, or Both) to turn on Water Pressure switch. You must have water in the fresh water system and water switch on BEFORE hitting the switch under the table for the hot water heater.
4.) Batteries....take a multi-meter and check the voltage on each battery with no charging (make sure switch is off under table if connected to shore power). They should all read around 12v. Flip the switch for the charger and take readings again, they should be at least 14v. You should also test that the engines are charging the batteries. NEVER switch the battery selector switches with the engines running. (Some systems can handle this - but play it safe and shut engines off before changing selector switch). On Napoleon here's what the switches do...
Starboard Battery Switch
Position 2 - House battery
Position 1 - Stb Start battery
Both - Stb Start and House battery
Port Battery Switch
Position 2 - Stb Start battery
Position 1 - Port Start battery
Both - Port and Stb start battery
Start the engines in each of the positions above to verify charging. Obviously start the engines only if in the water or properly connected to a water source.
5.) Fish box macerators...make sure able to pump out waster OK. You will need juice from your Starboard battery switch for these to work.
6.) All lights...inside and out.
7.) Windlass....
8.) Helm/steering...look for hydraulic fluid at foot of helm AND with a flashlight from inside the bow "state room". It's not an easy angle, but if the helm was leaking, it will collect at floor level beneath the level of the bed directly below the electrical panel. This will hopefully make sense when you are on the boat. The only way to reach into the area I'm referring to is with your left arm, laying on the bed, facing the electrical panel, again reaching under the bed from left to right.
9.) The plastic vent in the galley is often cracked...I had mine replaced and sized correctly (came too large from factory and thus cracked when installed).
10.) While running the shower, check behind the shower in compartment under the galley to see if hoses/fittings leaking.
11.) Verify engine hour meters working and advancing...
12.) Verify all windows open and close freely.
13.) Make sure you get all the goodies including dive ladder, ratchet tool for your windlass (allows you to manually crank if necessary and adjust gypsy for manual free fall), two sets of keys to engines and door, etc.
14.) Check for water in bow portion of sponsons...if present...likely coming from anchor rode locker leaking into them.
For some of these items, you may just opt to fix/upgrade yourself but these are some things to look at. Lastly, bring a notepad and a digital camera to document everything. This will make it easier to explain to the Service Manager. The inspection done properly should take several hours, not the 30 minute run around most people do
Good luck and remember ALL boats made will have these little issues to fix.