Search results

Thanks for your interest. C-Side has sold. Cheers, Kelly

Our trusted C-Side is up for sale, specifics are: C-Side 1999 C-Dory Cruiser Equipment list. 1999 22’ Cruiser C-Dory 1999 Twin Honda 50hp approx. 813 hours June 2015 compression tested 180+ all cylinders 1991 EZ Loader Trailer Single axle, surge brakes with new wheel bearings and bearing...

Hi Guys, Looking for a little advice here. My 22' Cruiser has a solar vent in the forward hatch cover installed by the original owner. It is circular and a hole was cut in the plexiglas, and the vent is sealed and held into place only by the original sealant. There are no mechanical...

A happy Thanksgiving, and a BEAUTIFUL day as well! Wishing all c-brats north and south of the US/Canada border the best. Piers Island is shining in the sun light today. Cheers, Kelly and Jeremy

C-WEED, have you found any other sources for these units? The original thread is 2005 and I've checked my local Walmart and their web site and haven't found anything like it. Any input most appreciated. Thanks, Kelly C-Side

That Honda 75's a 2 stroke right? Kicker?

As a recent new C-Dory owner and a fellow BC'er glad you made the "right" decision and welcome aboard. We are in Victoria and look forward to the chance where our paths might cross. We were in DeCourcy Island's Pirates Cove last weekend and saw what I'm sure were a couple of 21' Rangers in...

Thanks John and Papillon for your input. I have had a process described to me that involves drilling a pilot hole then doing a relief cut in the core that leaves the outside fibreglass in place. One would then fill the hole with fast cure epoxy and then drill the epoxy to install the screw. I...

Sorry for this dumb question, but better to ask and understand than not ask and stay in the dark. Am I safe in assuming the transom has enough solid wood (or plywood) not balsa core to mount the tabs with simple wood screws? I have watched the Bennet installation video and that appears to be...

Flagold, do you have a water separating fuel filter as well, or are you only running with the auto type filters and trowing them away when/if you see any water in the fuel? Does anyone have any suggestions for the best place to mount say the small Racor water separating filters? As they have...

Jeff, I'll be interested in seeing what you come up with. As a fan of the Yakima racks as well, I'd like to make use of some of the adapters I have and they sell to make these work too. Look forward to your posts and hopefully photos as well. K.

Slightly off topic, but in the same vein. I'm the proud new owner of a 22 Cruiser w/ twin Honda 50's. I have never fished with twin motors, and would appreciate any input on trolling with these beasts. Thanks in advance. Kelly

Thanks Bob, There is a clear plastic line that runs from the back of the cooler back to the sump just under the bulkhead to stern under the starboard window. this would in theory keep the drain from going into the cabin floor. I really only think we'd use the cooler for drinks on day trips...

I just did the first drill into a bulkhead on the Aft Cabin Door bulkhead. I noticed on my 1999 22" Cruiser, it felt like there was a hard layer though which I was drilling and a soft core into which th balance of the bit pentrated. I expected a solid core of marine grade plywood. Boy am I...

I've just landed my dream boat a 22" cruiser and notice the ice shelf in the cooler is not connected to the drain tube that takes the melted water to the bilge is not connected. I'm assuming the jagged edge on the bottom of the ice shelf that is particulartly short, used to have a 90 degree...

Thanks All, After a little googling ( is that a word) and exploration based on Sarge and Thataway's input I'm good to go. I'll try both in different locations and with any luck report back. Cheers, Kelly

I'm in process of outfitting C-Side with the appropriate safety gear to comply with Candian Coast Guard standards. One requirement is to have a minimum of two 5BC fire extinquishers on board, one is intended for the galley and the other for the engine area. I have identified a good spot for...

Sorry as usual I am late to the party. Just got my dory and am interested in driving another round of orders. Especially in Canada. As I am in Canada and we seem to be in the minority, perhaps if any canucks out there are interested and want to jump on the band wagon we can get an order...

I have just purchased my dream boat 22 ft. Cruiser and also inherited the dock lines and fender lines (and fenders) as well. These are terribly moss and fungi infested, and I have been trying to clean them. I have soaked them in a bucket with Simply Green cleaning detergent and since scrubbed...

Pictures? Age of motors? Contact info would be good. I'm interested. 250-661-2480 or ksidener@gentoosystems.ca Kelly