Search results

That was my normal cruising RPM. It should open up much more. I only openned it up once and not WOT. I never had any problems with speed and the motor checked out fine with the last service. Don't know what to tell you. Happy Cruising.

SOLD Thanks far all the inquirys and interest. We're going to miss the Lorraine J.

$20,000. Equiped with 2009 90HP ETEC, 1990 15HP Johnson Kicker, Hydraulic Trim Tabs, Humminbird GPS/Fish Finder, Downrigger, VHS Radio, Dual Batteries, Standard Equipment like twin 18 Gallon gas tanks, two burner Alcohol Stove, Dinette, Sink, Ice box, Porta Pottie. 1990 well maintained...

What a great picture of a Great boat. That's like mine. A 22 foot C-Dory Cruiser. Mine will go on the market this spring. Eqiuiped with a 2009 90HP ETEC. Great motor for a great boat. Bought the boat new in 1990.

I ordered replacement gaskets from American Marine Products, www.americanmarine.com. I ordered gasket number TP-240. I measured and ordered 53 feet for my 1990 22ft Cruiser adding a little extra to the order. They charged me 1.25/ft plus SH totaling $82.11. The old gasket and new gasket have...

I would go Evinrude ETEC. Because it's at least 100 pounds lighter, less maintenance, efficient, less moving parts and reliable. My new 90HP ETEC has a first maintenance schedule of 3 years. If your in the north and need to winterize it's all done automatic. But the big thing that sold me...

This was a wet spring and summer. The battery compartment on my 1990 Cruiser is full of Mold. Also in the battery compartment is electrical wires and the fuel fill hose. The bottom of the compartment is open in the back and my fuel tank is below the compartment. Now, how do I get rid of...

Yes, I now have canvas on my boat when on the mooring. This helps about 90% of the time. When I get heavy, wind blown rain, I still get water in the cockpit. That's not the issue. The issue is that is something to concider up front before you buy. My canvas is for storage and no cruising...

I noticed someone suggested a boat lift. Not practical where you are I believe because you have high tidal differences. I had a boat lift in Maryland that was great but we only had a two foot tide. I would love to have one here in Maine but we have a ten foot tide and icebergs in the winter.

I would go with either a 19 foot or 22 foot Angler. The Angler has more cockpit room for provisions. HOWEVER! One problem with C-Dory's is there is no floor on 22 foot and smaller. Your standing on the inside of the hull. No raised, skuppered floor. Therefore you will have wet feet from...

I run my boat in the Piscataqua River, Between Maine and New Hampshire, all of the time. This river has a very high current. I have a 1990 22 foot C-Dory Cruiser. My boat was equiped with a 1990 70 HP Johnson with the original prop. All purchased as a package in 1990. This current bounces...

Great picture. Thanks. I'll order up a couple samples and let you know what I come up with. Thanks again. The picture tells it all.

CView, Can you do me a favor? Go to www.americanmarine.com and look under Window. Click on Mariner Fixed. At the bottom of the page, click on replacement Gaskets. Where you had the old window gaskets out, can you tell me which profile on that page matches the gaskets you removed, if any. You...

Azul, CDory has changed window manufacturers. The older window frames are plain aluminum frames while the newer windows are all white painted aluminum frames. I replaced my center front window a couple years ago with one that opens. The new window has corners that a more round and not as...

I have a 1990 Cruiser. The grey window gaskets are shrinking in the corners and need replacement. This is an OLD thread but it was never answered. I have a source for replacement gaskets if they are still available, American Marine Products of Pompano Beach Florida. My Question is: Does...

I did notice a rise in RPM when I was out last. The rise was when I shifted to nuetral which I would think is normal. I'm putting the boat back in the water this week so I'll watch it closer. Only have 6 hours on it. I went with the ETEC 90 because in 1990 the Cruiser Transom was rated for...

I am seeing one problem. I have a minor vibration at 1200 RPM. I'm told that this is a resonance between the outboard and the transom and it is common amongst some outboard brands and some boats depending on the transom construction and material. The vibration starts and stops as I pass...

The dealer fitted my 90 HP ETEC with a 13.5 x 15 prop to get a WOT of 4900 RPM. That's what I'm told. They started with a 13.5 x 17 prop but the RPM wasn't right. Stevej, That link you gave me helped a lot. Thanks.

Just repowered my 1990 22ft Cruiser with a 2009 90HP Evinrude ETEC. Replacing the original 1990 70HP Johnson. What a HUGE difference. Ran super. Today was my first time out with it and I've traveled this distance with the old motor and used almost twice the gas. That old Johnson really...

I installed Bennett M120's on my 22 ft Cruiser and they work great. I had to opt to the optional position indicator so I could see where my tabs were at any given time. You can't beat Bennett's customer service either. They sent me shorter actuators and more tubing at no charge. I had to...