Search results

Seat swivels to face in different directions. The entire assembly can be removed with 2 bolts to convert back to original configuration.

Passenger seat reversed.

Storage box lid is mounted on hinges and much easier to access.

Passenger seat

Just looked closer at my photos, and will look at my boat later tomorrow, but I just don't think there is anyway you could mount the kicker directly to the transom with 12" Lenco Trim tabs, and clear them, unless you have the kicker trimmed up pretty hi. At least not with the kicker and boat I...

Kicker mounted to transom. fits like a glove but every thing clears.

Kicker mounted to transom full lock port. 5/8" clearance from Lenco trim tab.

Kicker mounted to transom full lock starboard

I Should add that mounted directly to the transom we always run our kicker tied to the main motor. If untied the housing of the kicker will make contact with the housing of the main motor before it reaches full lock to starboard. The only time I would possibly use the kicker untied would be in...

That looks like it was a nice install Bill. Where did you get those mounting brackets? I can think of a few things those could be used for.

Our Lenco Trim tabs are 9" wide by 12" Long. At a full lock turn to port the kicker comes about a half inch from the tab when tab is in the up position. Our kicker is a Honda BF8D long shaft.

Our boat has the Lenco trim tabs with a Honda BF90A with permatrim and an 8HP Honda long shaft kicker. I purchased a mini jacker and found that I did not need it. I mounted the kicker directly on the transom and it works great. Clearances are close, but everything does clear and it keeps the...

I recently purchased and installed a Garmin 7sv Sonar/Fishifinder. First time out I was loosing the bottom above 10knts. Tried turning to the left and no difference. Tried turning to the right, no difference. I may have it angled to far towards the bow and would try making that adjustment next...

I have worked with epoxy fiberglass quite a bit with the wood boats I have built. As an experiment I decided to build a fish box for one of them using 1" construction foam sheets. I sandwiched the foam in 10oz epoxy fiberglass, glued the pieces together with epoxy and then fiberglass taped all...

We are sorry to hear of your condition Dr Bob. We met you at a c-brat dinner in Sequim a couple of years ago right after we purchased our C-Dory and we really enjoyed talking to you and Marie. More than that I have enjoyed the opportunity to soak up your knowledge through your many posts on the...

I have been following along with this thread and there are some very interesting points that have been made. On the subject of raw sewage being discharged in to ocean and inland waterways, It is a fact that the greater metropolitan area of Victoria BC on Vancouver Island, Canada (population of...

As Harvey said, this is very recommencement of a bartender. The Bartender boats are very highly regarded as very sea worthy boats. the smaller ones do operate with outboards, while the larger size bartenders use inboards. This is like the smaller variety, yet uses an inboard. This is the first...

Don,t know what type of auto pilot you are using, but with our older Raymarine auto pilot we tie our 8hp kicker to the main and troll 1.5 to 2 mph all day in the strait of Juan DeFuca and unless it gets really rough or windy it works great. On ours there is a lot of settings as to how far the...

Hello Ron & Anne Sounds like you have both worked hard to make this a super event. We were looking forward to this for months. Unfortunately we need to report in that we will not be able to make the event at all due to a death in our family. We hope to meet up with you some other time. Best...

Here is my take on the subject. I have a trailer with the oil hubs and one with the bearing buddy grease hubs. With the grease hubs I take them apart once a year to know that every thing inside is in good condition and that there has been no salt water intrusion that would cause rapid decay of...