Search results

By the way that glue is great for all kinds of stuff, very strong, good to have aboard.

I have used a glue called E6000 on a small puncture one one of my large fenders with very good results. clean and rough out the area prior to applying a glob of that stuff, let it cure at least 48 hrs, more is better, before re inflating. I used masking tape to make the patch circular, that...

Looking forward to run into each other, either in Puerto Escondido, La Paz or somewhere in between. We will likely launch in San Carlos sometimes in November. Re: the trailer, I am sure you have made all necessary preparations for your trip down the Baja including 2 spares, a big breaker bar...

Micah, I tried without success to pm you to ask the following question: There is a red hull RT on D dock in San Carlos (Sonora) Marina could it be the one you previously owned? Alain

Sorry, just read your previous post: You ARE considering the Vulcan! Good choice.

The Vulcan made by Rocna is a very good fit on our bow and sets quickly. No hoop, something to consider.

In the splash well, secured to a padeye, Also feeds the kicker.

Fans: Caframo 747

How many Amps does it draw? I don't think you'll be able to run it very long unless you have a generator.

Engel is having a Summer sale on their MR040F-U1 ac/dc fridge $150 off plus free extended warranty. Limited time. I got one. https://www.engelcoolers.com/shop/12-vo ... 9UQAvD_BwE

I got the 13" yesterday, blades look a little flatter than the 15", we'll see what happens when back in the water. Thanks

The boat is mostly heavily loaded, aluminum prop, 0n a good day I'll get to 5k @ WOT playing around with tabs and motor trim. I usually reach high teens in knots then. This is all at sea level when sea conditions allow, hard to find a day with really flat water though, I am sure That makes a...

What prop size and pitch are you using when in full cruising mode (heavily loaded that is) and at sea level? What max rpm do you achieve with that prop? my 15 1/4 x 15 is not to snuff I am thinking of trying a 15.5 x 13.

I have 150 ft of chain with plenty of nylon behind on a 9 kg Vulcan, great set up for the windlass, so far no cons

Ron & Micah Ron, my holding tank is under the toilet bowl in the head, the water tank, under the splash well, as measured (10x30x20 approx.) is too big to remove even with an extra vertical hatch on the forward part of the well. I am hesitant to cut too many large holes in that area as I feel...

We are in Puerto Escondido right now on our 25. We left San carlos (Sonora) in March , slowly made our way down to La Paz and are now on our way back up to San carlos. I must say that I felt the same way you do about the water tank capacity on the C-Dory before our first trip down the Sea a...

Bob, to first try the inspection hole size before cutting the whole top off is now the new plan. I will have to wait until i am home though.

Progress report (or lack of it) Food coloring was added to empty tank along with a couple gallons of water: red water started slowly seeping in the bilge within a minute.. One last brain storm, it is obviously a small crack according to the rate of leaking, it is on the bottom of the tank or...

Bob, beads of cold sweat were forming on my forehead as I was reading your last post, I wish I had the confidence and abilities to undertake such a project but i really don't. In the event I am unable to locate that leak, I was thinking of just cutting out the very top of the tank itself and end...

I can only visually check the two sides and top, I would have to remove the tank (impossible without doing destructive stuff to the splash well) to see the front, back and bottom. The connection to the pump has been checked and triple checked since it was the first suspect and is consistently...