Search results

Sure enough I found wet rotted core directly above the patch on the hull. Whoever did the repair just fiberglassed over core damage and called it good!

After I removed some wet rotted balsa core I discovered they had actually removed some of the damaged core and squirted in some of that expanding foam insulation to "repair" the damage! (Note that I had to remove some of the cabin bulwark to give access to the repair area.)

I wasn't comfortable with what might be on the other side of that patch in the hull so that area will be opened up and removed. I also went over the floor with a moisture meter.

There was a painted section on the bottom of the hull that appeared "flat" - meaning it didn't follow the contour of the surrounding fiberglass. It just looked like a shoddy repair to me and I couldn't live with that.

I’m looking for your opinions on what the ideal window wiper setup on a 22’ Cruiser would be. The new 22 I saw at the Portland Boat Show today has electric pantograph wiper blades mounted at the top of the windows. My ‘99 came with manual wipers mounted at the bottom of the windows. As part of...

Yes, and cameras too. We get lots of cold rainy days in the PNW and when camera lenses get cold they fog up. Lots of uses for a little 800W hair dryer. Yes, laptops, and also chargers for cordless tool batteries.

Thank you for the kind words Bob. I still have my trusty K&E slide rule (kids today don't know what they're missing), but it never saw work anywhere near like what you father did with his. That's impressive! You should be able to zoom in for better detail. If viewing on a desktop, there should...

Well I thought it would be helpful to post a schematic of my power circuitry, but there are a couple problems with this. The jpeg my CAD system creates gets re-sized by this website, making it too blurry to read. My workaround was to make a pdf file, which is much smaller, but this website...

The small 1000W inverter is located under the starboard berth. Nothing critical will be powered by the inverter. It’s there primarily as a convenience for any portable battery chargers that require 120VAC, as well as a small hair dryer that can be used to dry things out. Thus it is not switched...

Here's a link to a pdf (jpeg was too large) of my power schematic. It shows all proposed electrical wiring on the boat except individual fused DC circuits. If you're on a desktop you can use the little "+" icon in the upper right to zoom in. If you're on a cell phone just zoom with your...

This switch needs to be at the helm in the event of a LiFePO4 house battery shutdown. It switches the house loads between the house battery and the start battery. The cables coming from the batteries to this switch are AWG 2 and fused for 60A. This is far more capacity than is typically needed...

What are you referring to as crucial controls. Isn’t the switch panel in the photo the standard location used for all C-Dory Cruisers? I will be redesigning (fiberglass work) the helm area, but I’m planning on putting critical switches (horn, wipers) in the same general area. Yes, I apologize...

Here's a link to a hi-res jpeg drawing of my helm design. If you're on a desktop you can use the little "+" icon in the upper right to zoom in. If you're on a cell phone just zoom with your fingers... https://www.dropbox.com/scl/fi/o1qdsn4h ... zb3to&dl=0

Oh man - such good feedback! I'll address ssobol's comment first. Will get to Bob's hopefully tonight. I'm also going to try to figure out another way to post the helm drawing. The C-Brats website resizes the jpeg, causing small details to blur. There are three reasons I like having the little...

Helm design 12

I’ve had plenty of time to think through the helm design for my 22’ Cruiser restoration and would like to offer it up for criticism before I start modifying the fiberglass at the helm. Keep in mind that I’m an engineering nerd so there will likely be things about this design you don’t like and...

Helm design 12-1

Helm design 12-2

I have a 25 gal. Moeller Marine starboard plastic fuel tank that came out of a 1999 C-Dory 22’ Cruiser. The port tank cracked when I tried to remove a fitting, so I decided to replace both tanks with new. If you want it you can have it, but there’s a catch… I don’t have time to box and ship this...

fuel tank