Rear plastic cover removed showing 2 of 3 internal anodes. 3rd is lower right of engine (no picture)

Rear plastic cover removed showing 2 of 3 internal anodes. 3rd is lower right of engine (no picture)

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
Rear plastic cover for 2 of 3 internal anodes

Rear plastic cover for 2 of 3 internal anodes

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
Internal lower anode after cleaning

Internal lower anode after cleaning

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
Internal lower anode before cleaning

Internal lower anode before cleaning

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
Internal upper anode after cleaning

Internal upper anode after cleaning

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
Internal upper anode before cleaning

Internal upper anode before cleaning

  • Media owner Dora~Jean
  • Date added Apr 12, 2016
  • Reaction score 0
  • Comments 0
PICT0650

PICT0650

  • Media owner Dora~Jean
  • Date added Feb 10, 2009
  • Reaction score 0
  • Comments 0
Engine Tilt Position Sensor Clamp

Engine Tilt Position Sensor Clamp

  • Media owner Dora~Jean
  • Date added Jun 9, 2008
  • Reaction score 0
  • Comments 0
New brakes, old rotor. Next changeout I'll replace rotors with SS (Pacific Trailer at the time did NOT recommend SS rotors -- too many warped).

New brakes, old rotor. Next changeout I'll replace rotors with SS (Pacific Trailer at the time did NOT recommend SS rotors -- too many warped).

  • Media owner Dora~Jean
  • Date added Apr 30, 2007
  • Reaction score 0
  • Comments 0
Big difference between inside and outside pad wear. I honed down the slider pin and lubed well to equalize the wear (hopefully).

Big difference between inside and outside pad wear. I honed down the slider pin and lubed well to equalize the wear (hopefully).

  • Media owner Dora~Jean
  • Date added Apr 30, 2007
  • Reaction score 0
  • Comments 0
Compressing the piston for new pads.

Compressing the piston for new pads.

  • Media owner Dora~Jean
  • Date added Apr 30, 2007
  • Reaction score 0
  • Comments 0
YamahaVacuumGaugeSet

YamahaVacuumGaugeSet

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
Flywheel aligned to its mark (which results in the cam sprockets off by 1 notch -- next picture).

Flywheel aligned to its mark (which results in the cam sprockets off by 1 notch -- next picture).

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
This shows the alignment of the cam sprockets when the flywheel shaft notch is aligned with its "visible" mark with the flywheel "in place" -- makes a difference.

This shows the alignment of the cam sprockets when the flywheel shaft notch is aligned with its "visible" mark with the flywheel "in place" -- makes a difference.

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
With vacuum fittings in place

With vacuum fittings in place

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
Synchronizing the carbs -- Vacuum ports with manifold sealing bolts in place

Synchronizing the carbs -- Vacuum ports with manifold sealing bolts in place

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
Set of four vacuum fittings

Set of four vacuum fittings

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
Other end of vacuum fitting

Other end of vacuum fitting

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
Original 6mm sealing bolt from engine (top). My fabbed vacuum fitting from a 6mm coupler, 6mm bolt cut off with an added nut. Used epoxy on the threads to seal.

Original 6mm sealing bolt from engine (top). My fabbed vacuum fitting from a 6mm coupler, 6mm bolt cut off with an added nut. Used epoxy on the threads to seal.

  • Media owner Dora~Jean
  • Date added Apr 22, 2007
  • Reaction score 0
  • Comments 0
D

Synchronizing the carbs -- Vacuum ports with manifold sealing bolts in place

  • Items 19
  • Album owner Dora~Jean
  • Date created
There are no comments to display.

Album information

Category
Engine Maint
Album owner
Dora~Jean
Date created
Item count
19
View count
3,050
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

D

Dora~Jean

Media items
175
Albums
12
Can view media items
Inherited from category
Can add media items
Album owner only

Share this album

Back
Top