View previous topic :: View next topic |
Author |
Message |
bluedawg
Joined: 04 Sep 2018 Posts: 8 City/Region: Sterling
State or Province: AK
C-Dory Year: 2007
C-Dory Model: 22 Cruiser
Vessel Name: Blue Dawg
Photos: Blue Dawg
|
Posted: Wed Sep 05, 2018 12:10 pm Post subject: Both tachs stopped working |
|
|
Hello, I just bought Blue Dawg, a 2007 22' cruiser with twin Honda 40's. I am having some electrical issues that I am working through and one of them that the previous owner had not fixed is neither tachometer is working. He stated that they both quit working so he replaced them and the new ones didn't work either. I assume there is a blown fuse somewhere or possibly a rectifier issue? Any help on what and where to check first would be greatly appreciated. |
|
Back to top |
|
|
digger
Joined: 02 Nov 2003 Posts: 496 City/Region: Spokane
State or Province: WA
C-Dory Year: 1993
C-Dory Model: 22 Angler
Vessel Name: C-Sik
Photos: Snoopy-C
|
Posted: Wed Sep 05, 2018 5:18 pm Post subject: |
|
|
make sure on the throttle control box that all plugs are attached. Often there are three wires going from that to each tach. Usually there is a short wiring loom that has a connector that goes forward from each controller. |
|
Back to top |
|
|
bluedawg
Joined: 04 Sep 2018 Posts: 8 City/Region: Sterling
State or Province: AK
C-Dory Year: 2007
C-Dory Model: 22 Cruiser
Vessel Name: Blue Dawg
Photos: Blue Dawg
|
Posted: Wed Sep 05, 2018 5:26 pm Post subject: |
|
|
okay, I will make sure to look there. Thanks! |
|
Back to top |
|
|
MOOSE
Joined: 07 Nov 2003 Posts: 619 City/Region: Rainy Lake - Int'l. Falls
State or Province: MN
C-Dory Year: 2001
C-Dory Model: 22 Cruiser
Vessel Name: MOOSE
Photos: MOOSE
|
Posted: Thu Sep 06, 2018 8:41 am Post subject: |
|
|
And, as strange as it may sound, make sure your battery cables are tightly secured to the battery lugs. I had a tach problem too once and this ended up being the solution. I now use two hex nuts, one as a lock nut on top of the other, rather than wing nuts. _________________ .....and remember, if the women don't find you handsome, they should at least find you handy. |
|
Back to top |
|
|
BrentB
Joined: 15 Jul 2006 Posts: 4419 City/Region: Greenwood
State or Province: IN
Photos: BrentB
|
Posted: Thu Sep 06, 2018 10:29 am Post subject: |
|
|
I would look for a outboard rigging manual _________________ Brent Barrett |
|
Back to top |
|
|
BrentB
Joined: 15 Jul 2006 Posts: 4419 City/Region: Greenwood
State or Province: IN
Photos: BrentB
|
Posted: Thu Sep 06, 2018 11:38 am Post subject: |
|
|
for wiring colors and harness connector position. might be a broken wire, loose or poor connection. Purchase electrical contact cleaner to clean |
|
Back to top |
|
|
tsturm
Joined: 01 Nov 2003 Posts: 1134 City/Region: Soldotna
State or Province: AK
C-Dory Year: 2003
C-Dory Model: 25 Cruiser
Vessel Name: JMR TOO
Photos: JMR-TOO
|
Posted: Thu Sep 06, 2018 11:47 am Post subject: |
|
|
MOOSE wrote: | And, as strange as it may sound, make sure your battery cables are tightly secured to the battery lugs. I had a tach problem too once and this ended up being the solution. I now use two hex nuts, one as a lock nut on top of the other, rather than wing nuts. |
Also make sure all wires are connected at the batt., check fuses under each engine cowl, & inline near the control box (shift -throttle).
|
|
Back to top |
|
|
bluedawg
Joined: 04 Sep 2018 Posts: 8 City/Region: Sterling
State or Province: AK
C-Dory Year: 2007
C-Dory Model: 22 Cruiser
Vessel Name: Blue Dawg
Photos: Blue Dawg
|
Posted: Thu Sep 06, 2018 12:33 pm Post subject: |
|
|
Well last night I took off all battery cables and cleaned them well, I also had the battery tested and it checked out (brand new Interstate). Now comes the really screwy part, I have been getting low voltage alarms on my Garmin but when I put a tester on the battery it shows 12.2 volts so I started the starboard motor and ran the rpms ups a bit and put the meter back on the house battery and it only went up to about 12.8 volts. when I did the same thing with the port motor and put my meter on its battery it went to ~13.3 volts.
Wait it gets better, I hooked everything back up and then this morning went to look everything back over and checked the battery still 12.2 (I did have the house switch off all night) but the Garmin will not turn on, you can see that the buttons will barely light up but nothing turns on. I also noticed that when trying to turn on the Garmin that the tachs were lighting up as well. I am soooooo lost. I made sure that all cables were clean and snug and none look or feel in bad shape.
|
|
Back to top |
|
|
BrentB
Joined: 15 Jul 2006 Posts: 4419 City/Region: Greenwood
State or Province: IN
Photos: BrentB
|
Posted: Thu Sep 06, 2018 1:06 pm Post subject: |
|
|
you might look at engine side battery cables. Disconnect at battery or switch for no voltage with your DVM, then remove, clean, reinstall and tighten |
|
Back to top |
|
|
BrentB
Joined: 15 Jul 2006 Posts: 4419 City/Region: Greenwood
State or Province: IN
Photos: BrentB
|
Posted: Thu Sep 06, 2018 1:24 pm Post subject: |
|
|
something is amiss
Fully charged batteries should measure at 12.6 volts or above at rest. When the engine is running, this measurement should be 13.7 to 14.7 volts.
Loose or poor cables? easy to check. remove and clean
Battery needs load testing.
Alternator and regulator needs checking |
|
Back to top |
|
|
Avidmagnum12
Joined: 23 Mar 2013 Posts: 673 City/Region: Ocklawaha
State or Province: FL
C-Dory Year: 2011
C-Dory Model: 25 Cruiser
Vessel Name: C-Otter
Photos: C-Otter
|
Posted: Thu Sep 06, 2018 11:49 pm Post subject: |
|
|
One other thing you mite consider is the size of the wire going from the battery to the buss by the helm. I had this problem on my 22 until I ran larger power and ground wires to the buss. Too many things for the size of the wire. We tend to add more toys to the boats over time. _________________ Tom and Joyce Schulke
2011 CD 25 "C-Otter" 07/2015 to present
2011 CD 25 "My Girl" 06/2015 renamed C-Otter
2004 CD 22 Commuter "Out2C" 03/10 to 06/15 |
|
Back to top |
|
|
bluedawg
Joined: 04 Sep 2018 Posts: 8 City/Region: Sterling
State or Province: AK
C-Dory Year: 2007
C-Dory Model: 22 Cruiser
Vessel Name: Blue Dawg
Photos: Blue Dawg
|
Posted: Fri Sep 07, 2018 12:15 pm Post subject: |
|
|
Okay guys, first thank you for the ideas and trying to help. I gave everything another look over last night and the only wiring I found that was in less than perfect condition was the 50 AMP thermal circuit breaker. I had initially looked past this because the terminals were covered by tiny rubber caps. Once I removed those I could see that they were extremely corroded. When I tried to remove the nuts they both broke. I think NAPA has a replacement so I will pick it up today and install it and also freshen up the lengths of wire going to it. Again thanks for the help. I will report back with the results. |
|
Back to top |
|
|
Sea Wolf
Joined: 01 Nov 2003 Posts: 8650 City/Region: Redding
State or Province: CA
C-Dory Year: 1987
C-Dory Model: 22 Cruiser
Vessel Name: Sea Wolf
Photos: Sea Wolf
|
Posted: Fri Sep 07, 2018 3:50 pm Post subject: |
|
|
Check the battery cables themselves with the multi-meter for resistance.
If water, particularly salt water, is allowed to get into the space inside the insulation with the copper conductors, corrosion can set in and limit or destroy their conductivity.
This is why marine cables are tinned with a tin coating to help protect the copper underneath from corrosion, but add enough salt, particularly back near the splash well/motor well, and all bets are off.
Good Luck!
Joe. _________________ Sea Wolf, C-Brat #31
Lake Shasta, California
"Most of my money I spent on boats and women. The rest I squandered'. " -Annonymous |
|
Back to top |
|
|
AstoriaDave
Joined: 31 Oct 2005 Posts: 994 City/Region: Astoria
State or Province: OR
|
Posted: Fri Sep 07, 2018 4:58 pm Post subject: |
|
|
bluedawg wrote: | Okay guys, first thank you for the ideas and trying to help. I gave everything another look over last night and the only wiring I found that was in less than perfect condition was the 50 AMP thermal circuit breaker. I had initially looked past this because the terminals were covered by tiny rubber caps. Once I removed those I could see that they were extremely corroded. When I tried to remove the nuts they both broke. I think NAPA has a replacement so I will pick it up today and install it and also freshen up the lengths of wire going to it. Again thanks for the help. I will report back with the results. | bluedawg,
If the connectors on that 50 A breaker are that corroded, it is likely that you have bad connections at other locations also. And, it is very likely the wiring is shot in some stretches, from your description. Untinned wiring (aka bare copper under the insulation), over time, will corrode, forming a dark material. The wiring can look OK until you peel back an inch or so of insulation. This corrosion can run the entire length of a wiring run.
How old is the wiring? Did the previous owner mention whether he replaced major sections?
Those two tachs might be dead if they have poor connection(s) to ground. You should pull the switch/breaker housing and check the condition of the connections there, also. _________________ Dave Kruger
Astoria, OR |
|
Back to top |
|
|
bluedawg
Joined: 04 Sep 2018 Posts: 8 City/Region: Sterling
State or Province: AK
C-Dory Year: 2007
C-Dory Model: 22 Cruiser
Vessel Name: Blue Dawg
Photos: Blue Dawg
|
Posted: Fri Mar 08, 2019 5:08 pm Post subject: |
|
|
It has been a long winter but I am diving back into this tomorrow. I have found several connections that are corroded at the crimp (and probably into the wire too) so I am going to start cutting all of that out. It looks like someone has been using cheap wire and connectors that are not tinned to make repairs and that is where most of the damage is. Luckily the starter wires and wiring going to the main switch panel in the v-berth look to be in great condition. The main problem is the wiring installed or repaired going to the pot puller, washdown pump and stuff like that. I bought a to of splicers and other connectors and plan to replace everything that is looking rough. The only other thing that has stuck out so far is my battery switches that have a bit of surface corrosion, at first I figured replace them just to be safe but they are pretty pricey. What do you guys think? Can I just polish these up a bit? |
|
Back to top |
|
|
|