Molded insert replacements for cockpit of 25"

Schuster

I have a 2007 25' and have decided that I would like to replace the cockpit bulkhead plastic molded inserts that are use for rod holders, deck brush etc. Does anyone know where I can order these from?

srbaum · Posted: Sat Jan 27, 2024 2:59 pm Post subject:

Dave,
Can you post a photo?

Salmon Fisher · Posted: Sat Jan 27, 2024 5:06 pm Post subject:

I wonder if the inserts you have are the same as what is installed in new
25 Cruisers? I would check with the factory.

Here are couple possibilities:

https://www.greatlakesskipper.com/boat-parts/boat-doors-hatches-port-windows/storage-boxes/l/parts-brand:north-american-plastics?amp%3Bp=2%2F%2F

https://www.tradeinn.com/waveinn/en/nuova-rade-utility-storage-case-side-mount-with-glass-holder-right/1223770/p?utm_source=google_products&utm_medium=merchant&id_producte=1251702&country=us&gad_source=1&gclid=CjwKCAiA8NKtBhBtEiwAq5aX2FwjV8B_xwtFmxk3c-9dCD7XsX5Z7VsRsD_6OLHEBIzRbm50xqITdRoCz5oQAvD_BwE&gclsrc=aw.ds

Salmon Fisher · Posted: Sat Jan 27, 2024 5:46 pm Post subject:

On this page is what Colby Smith did to repair his.

http://www.c-brats.com/viewtopic.php?t=244&postdays=0&postorder=asc&start=4140

colbysmith · Posted: Sat Jan 27, 2024 10:20 pm Post subject:

I repaired one, but one was too bad, so I purchased new. Went through NMI, Tom at the time, although I don't beleive he is still there. I think they were like $250 or so. Colby

Schuster · Posted: Sun Jan 28, 2024 10:27 am Post subject:

Thanks for the replies everyone. Steve I am unable to post a picture of the insert at this time, but the picture in Colby's post is as near as I can remember identical. I'm not sure of the measurements at this time either. Colby, I will check with NMI and hopefully come up with a solution. Patrick thank you for reply, very helpful but I guess I will need to get some measurements before I go any further. Hoping to get this done before May 1.

Salmon Fisher · Posted: Sun Jan 28, 2024 3:27 pm Post subject:

Maybe this one will fit.

https://www.greatlakesskipper.com/sailfish-boat-coaming-storage-bin-51-2049-30-06-wa-w-net-ivory

Schuster · Posted: Mon Jan 29, 2024 11:28 am Post subject:

Thanks Patrick, I saw that one and it looks pretty close. The netting on that could be changed to put in the hard front retainer wall from the original inserts. I'll have to check the measurements for opening on the existing set up. That is where I store my 15lb downrigger weights when not in use so need something substantial.

jkidd · Posted: Mon Jan 29, 2024 4:23 pm Post subject:

I modified mine on my 22 so they could carry a little more and a little more weight.

DayBreak · Posted: Mon Jan 29, 2024 5:20 pm Post subject:

Jody, looks nice. I bet it holds lots of fishing items or whatever you want to put in there. Nice job!

I also like that electric plug for your Scotty Downrigger. Can you give us a name and part number for that plug. I don't like the original Scotty round plug as it tends to lose contact or not make contact easily unless you wiggle the connection just right. I have a friend who also has the same issue with his Scotty Downrigger. I know saltwater is the enemy with electrical connections but I need to try something different. Gary

jkidd · Posted: Mon Jan 29, 2024 8:31 pm Post subject:

Schuster · Posted: Mon Jan 29, 2024 9:36 pm Post subject:

Thanks Jody, that looks very similar to mine. I've got the faceplate but not the bottom plate or the dividers.

DayBreak · Posted: Mon Jan 29, 2024 9:45 pm Post subject:

[quote="jkidd] It's a 50 amp Anderson connector you can get them off Amazon or Cabelas.[/quote]

👍 Thanks Jody