The C-Brats Forum Index
HomeForumsMy TopicsCalendarEvent SignupsMemberlistOur C-DorysThe Brat MapPhotos

 Thataway 
Screw (rusted, with damp core) and bracket removed, damp core removed and dryed, filled with epoxy and fillet, then glass to bond floor to step face, eliminating any screws into the core
Screw (rusted, with damp core) and bracket removed, damp core removed and dryed, filled with epoxy and fillet, then glass to bond floor to step face, eliminating any screws into the core
Viewed: 1963 times.

Screw holes in boat hull core filled with epoxy, after being undercut, then fillet to Decaboard, with sanding boat bottom and then laminating biaxial between decaboard and the boat bottom--no more screws into the core.
Screw holes in boat hull core filled with epoxy, after being undercut, then fillet to Decaboard, with sanding boat bottom and then laminating biaxial between decaboard and the boat bottom--no more screws into the core.
Viewed: 1881 times.

Hole, filled with clear epoxy, where 2\
Hole, filled with clear epoxy, where 2\" #12 screw went into either core or support for foreward deck--was damp, dryed, epoxied and screw reset with sealant. The joint between the cockpit floor and aft bulkhead is now sealed to prevent any further water intrusion.
Viewed: 1829 times.

Note the dirt on the foreward lip, and no bedding on the frame.
Note the dirt on the foreward lip, and no bedding on the frame. *
Viewed: 2123 times.

Moisture on plwywood both from screw holes and from around the lack of caulking
Moisture on plwywood both from screw holes and from around the lack of caulking
Viewed: 1811 times.

Two trim screw holes where water was comming thru the deck from hatch lack of bedding
Two trim screw holes where water was comming thru the deck from hatch lack of bedding
Viewed: 1839 times.

Foreward part of hatch plywood, with spray of gel coat over the raw edge
Foreward part of hatch plywood, with spray of gel coat over the raw edge
Viewed: 1824 times.

initial photo after the \
initial photo after the \"flapper\" valve is taken off. There is gel coat smeared over the wood boring, and some voids. *
Viewed: 2089 times.

Wood sanded clean--notice a small void at the very back, where the aft deck is attatched
Wood sanded clean--notice a small void at the very back, where the aft deck is attatched
Viewed: 1757 times.

Void from the inside, cleaned out for glass application
Void from the inside, cleaned out for glass application
Viewed: 1712 times.

a layer of glass fibers and a layer of 10 oz cloth laid over the void with epoxy.  A second layer of cloth is placed over this and into the transom opening
a layer of glass fibers and a layer of 10 oz cloth laid over the void with epoxy. A second layer of cloth is placed over this and into the transom opening
Viewed: 1804 times.

Final layer of epoxy, and 10 oz glass covering the hole, with two layers of 10 oz glass covering and tying the void in the foreward area--all water tight.
Final layer of epoxy, and 10 oz glass covering the hole, with two layers of 10 oz glass covering and tying the void in the foreward area--all water tight. *
Viewed: 1990 times.

Fast set epoxy
Fast set epoxy *
Viewed: 1902 times.

fast set epoxy and screws to make a right angle bracket to hold a fuel pump
fast set epoxy and screws to make a right angle bracket to hold a fuel pump
Viewed: 1707 times.

West systems epoxy and hardner
West systems epoxy and hardner
Viewed: 1688 times.

fillers: cabosil, microlite and microfibers
fillers: cabosil, microlite and microfibers
Viewed: 1616 times.

epoxy and hardner mixed in cup
epoxy and hardner mixed in cup
Viewed: 1591 times.

adding cabosil by the Pinch
adding cabosil by the Pinch
Viewed: 1626 times.

Cabosil thickened and addition of microlite filler
Cabosil thickened and addition of microlite filler
Viewed: 1601 times.

Mixed to peanut butter consistancy ready to spread
Mixed to peanut butter consistancy ready to spread
Viewed: 1645 times.

filler in area where fillet will be formed
filler in area where fillet will be formed
Viewed: 1692 times.

Fillet created with spreader tool
Fillet created with spreader tool
Viewed: 1718 times.

final fillet
final fillet
Viewed: 1639 times.

finel fillet from side
finel fillet from side
Viewed: 1673 times.

* Comments available for this item.
Powered by Gallery v1



Page generation time: 1711655198.88s (PHP: 100% - SQL: 0%) - SQL queries: 9 - GZIP disabled - Debug on