The C-Brats Forum Index
HomeForumsMy TopicsCalendarEvent SignupsMemberlistOur C-DorysThe Brat MapPhotos

 Greeniron 
July 2002, Picked up new C-Dory @ Northwest Outlet, Superior, Wi., and trailer home to Va.
July 2002, Picked up new C-Dory @ Northwest Outlet, Superior, Wi., and trailer home to Va. *
Viewed: 1117 times.

March 2003 Here's the new Johnson 4stroke in it's steel rack after I striped the cardboard away.
March 2003 Here's the new Johnson 4stroke in it's steel rack after I striped the cardboard away.
Viewed: 747 times.

After taking the weight of the motor with the lift, I unbolted the steel cage away, ready to wheel over to the boat.
After taking the weight of the motor with the lift, I unbolted the steel cage away, ready to wheel over to the boat. *
Viewed: 715 times.

On this warm March day, with my wife and son helping me, let's hang it!
On this warm March day, with my wife and son helping me, let's hang it!
Viewed: 639 times.

Glad to have the wife here, she is a perfectionist, and won't let me hurry along. Let's see, first thing we need to do is level every thing up.
Glad to have the wife here, she is a perfectionist, and won't let me hurry along. Let's see, first thing we need to do is level every thing up.
Viewed: 691 times.

Late in the after noon, we have it bolted up right where we wanted it, with the ventilation plate 1/8
Late in the after noon, we have it bolted up right where we wanted it, with the ventilation plate 1/8" below the bottom of the boat. Thanks family for helping me do a job well done.
Viewed: 710 times.

Here's another look.
Here's another look.
Viewed: 660 times.

By May, we have Greeniron ready for sea trials. Only problem was motor would not run much above idle. Bypassed fuel selector valve, ran good. Later, took valve apart, what a mess,  all gooped up with sealer, and plumed wrong.
By May, we have Greeniron ready for sea trials. Only problem was motor would not run much above idle. Bypassed fuel selector valve, ran good. Later, took valve apart, what a mess, all gooped up with sealer, and plumed wrong.
Viewed: 845 times.

Here's the crew, the boy is begging food from Mama, there's a little black beagle running around here somewhere too. At Buggs Isl. Lake, Va.-NC. Water temp. 87*
Here's the crew, the boy is begging food from Mama, there's a little black beagle running around here somewhere too. At Buggs Isl. Lake, Va.-NC. Water temp. 87*
Viewed: 1170 times.

103-0372_IMG_2
remote eastern shore Chesapeake Bay.
103-0372_IMG_2
remote eastern shore Chesapeake Bay.
Viewed: 802 times.

Lake Powell the magnificent
Lake Powell the magnificent
Viewed: 580 times.

Powell
Powell
Viewed: 551 times.

Thumpers tonight Lake Powell August 007
Thumpers tonight Lake Powell August 007 *
Viewed: 617 times.

25\' Cruise Ship
25\' Cruise Ship
Viewed: 161 times.

25\' Cruise Ship. Notice it is shown with a inboard-out board for power.
25\' Cruise Ship. Notice it is shown with a inboard-out board for power.
Viewed: 179 times.

Friday Harbor, Dog friendly town.
Friday Harbor, Dog friendly town.
Viewed: 180 times.

Change cam drive belt on 2002, 70hp Johnson. Service manual said do @ 200 hours. Now it's been extended to 800 hours.
Change cam drive belt on 2002, 70hp Johnson. Service manual said do @ 200 hours. Now it's been extended to 800 hours.
Viewed: 177 times.

Using special  OMC tools, remove flywheel bolt.
Using special OMC tools, remove flywheel bolt.
Viewed: 177 times.

OMC tools, pop flywheel off tapered shaft.
OMC tools, pop flywheel off tapered shaft.
Viewed: 169 times.

Remove alternator, and belt tension pulley.
Remove alternator, and belt tension pulley.
Viewed: 178 times.

With timing marks properly aligned, remove belt, install new one, and reassemble.
Flywheel installs with notch on keyway on tapered shaft. Belt tension pulley has spring loading for belt tension, over tension can damage oil pump drive at bottom of cam shaft.
With timing marks properly aligned, remove belt, install new one, and reassemble.
Flywheel installs with notch on keyway on tapered shaft. Belt tension pulley has spring loading for belt tension, over tension can damage oil pump drive at bottom of cam shaft.
Viewed: 245 times.

* Comments available for this item.
Powered by Gallery v1



Page generation time: 1560861981.33s (PHP: 100% - SQL: 0%) - SQL queries: 8 - GZIP disabled - Debug on