The C-Brats Forum Index
HomeForumsMy TopicsCalendarEvent SignupsMemberlistOur C-DorysThe Brat MapPhotos

 Drifter 
15/09/2011...new EZ-Loader Bunk trailer
15/09/2011...new EZ-Loader Bunk trailer
Viewed: 849 times.

15/09/2011...new ez-loader trailer..bunk side guides need to be raised. Boat is sitting too high on the trailer/frame needs to be lowered
15/09/2011...new ez-loader trailer..bunk side guides need to be raised. Boat is sitting too high on the trailer/frame needs to be lowered
Viewed: 819 times.

15/09/2011...new ez-loader trailer
15/09/2011...new ez-loader trailer
Viewed: 848 times.

18/09/2011...installed a female plug reciever for the trailer plug..keeps the plug from flopping around
18/09/2011...installed a female plug reciever for the trailer plug..keeps the plug from flopping around *
Viewed: 1020 times.

18/09/2011..installed a hose clamp to support the trailer pigtail...the only thing that was holding the wiring was the grounding wire.
18/09/2011..installed a hose clamp to support the trailer pigtail...the only thing that was holding the wiring was the grounding wire.
Viewed: 824 times.

18/09/2011..flipped the leaf springs on my axles today..this lowers the boat by about 3-4 inches
18/09/2011..flipped the leaf springs on my axles today..this lowers the boat by about 3-4 inches
Viewed: 762 times.

18/09/2011...raised the center fender supports by 2.5 inches,the fenders front and back have alot of tire clearence already.All looks great, you cann't see any alterations.
18/09/2011...raised the center fender supports by 2.5 inches,the fenders front and back have alot of tire clearence already.All looks great, you cann't see any alterations.
Viewed: 799 times.

03/10/2011...Coho fishing early this morning,beautiful day plus i had the river to myself.
03/10/2011...Coho fishing early this morning,beautiful day plus i had the river to myself.
Viewed: 724 times.

04/10/2010 Pulled my boat for the season while the weather is warm enough to do some bottom painting. Tomorrow i will put the front trailer jack on a bathroom scale to check the tounge weight.I think the axiles need to be moved forward about six inches.There seems to be more weight on the forward tires.
04/10/2010 Pulled my boat for the season while the weather is warm enough to do some bottom painting. Tomorrow i will put the front trailer jack on a bathroom scale to check the tounge weight.I think the axiles need to be moved forward about six inches.There seems to be more weight on the forward tires. *
Viewed: 1018 times.

04/10/2011..not to trilled about my new ez-loader trailer.Rides so high!!!Rick Norman from ez-loader says my boat ( sent him a picture ) is loaded correct but i need to take the front ends of the bunks up a notch so the the boat just clears the roller/really shouldn't be any weight on the front roller
04/10/2011..not to trilled about my new ez-loader trailer.Rides so high!!!Rick Norman from ez-loader says my boat ( sent him a picture ) is loaded correct but i need to take the front ends of the bunks up a notch so the the boat just clears the roller/really shouldn't be any weight on the front roller
Viewed: 820 times.

06/10/2011....moved the boat on level ground to check boat/trailer levelness
06/10/2011....moved the boat on level ground to check boat/trailer levelness
Viewed: 790 times.

06/10/2011.. placed level on forward section of the tongue...close enough for leaf springs on a tandem
06/10/2011.. placed level on forward section of the tongue...close enough for leaf springs on a tandem
Viewed: 792 times.

06/10/2011...measured from ground to bottom of hitch ball receiver....21 inches
06/10/2011...measured from ground to bottom of hitch ball receiver....21 inches
Viewed: 743 times.

06/10/2011...measured from the top of rear boom just before the taillights to the ground...21 inches
06/10/2011...measured from the top of rear boom just before the taillights to the ground...21 inches
Viewed: 768 times.

06/10/2011.scrubbed floors interior and washed exterior
06/10/2011.scrubbed floors interior and washed exterior
Viewed: 753 times.

06/10/2011..all cleaned for the winter
06/10/2011..all cleaned for the winter
Viewed: 754 times.

06/10/2011..removed the gas and cleaned the inside of the tanks.Painted the tanks and checked fuel lines.
06/10/2011..removed the gas and cleaned the inside of the tanks.Painted the tanks and checked fuel lines.
Viewed: 813 times.

07/10/2011..bottom painted the boat today,did most of the boat even though it really only needed it where the keel roller came in contact with the boat.
07/10/2011..bottom painted the boat today,did most of the boat even though it really only needed it where the keel roller came in contact with the boat.
Viewed: 728 times.

07/10/2011..bottom paint,also touched up the propeller with black rust paint.
07/10/2011..bottom paint,also touched up the propeller with black rust paint.
Viewed: 773 times.

07/10/2011..Port side bottom paint, when i removed the bunk load guides i noticed that one was 2 inch longer past the aft support post than the other.
07/10/2011..Port side bottom paint, when i removed the bunk load guides i noticed that one was 2 inch longer past the aft support post than the other.
Viewed: 806 times.

07/10/2011  finished product, i will leave the boat on the boat stands for a couple of days to dry.
07/10/2011 finished product, i will leave the boat on the boat stands for a couple of days to dry.
Viewed: 756 times.

08/10/2011..used 3M Marine Rubbing Compound than Collinite's No. 925 Fiberglass Boat Wax on the Black trim...by hand.I got a shine but there are still streaks embedded into the 1985 gel-coat
08/10/2011..used 3M Marine Rubbing Compound than Collinite's No. 925 Fiberglass Boat Wax on the Black trim...by hand.I got a shine but there are still streaks embedded into the 1985 gel-coat
Viewed: 826 times.

08/10/2011..removed these  fittings from the inside gunnels..guess they are fitting from a previous CrabPot puller
08/10/2011..removed these fittings from the inside gunnels..guess they are fitting from a previous CrabPot puller
Viewed: 764 times.

08/10/2011..removed the screws that secured the P66 transducer.. dipped them in thickened West System epoxy and reinstalled them.I than used 3M 4200 to cover remaining gaps.
08/10/2011..removed the screws that secured the P66 transducer.. dipped them in thickened West System epoxy and reinstalled them.I than used 3M 4200 to cover remaining gaps.
Viewed: 828 times.

* Comments available for this item.
Powered by Gallery v1



Page generation time: 1711719793.53s (PHP: 100% - SQL: 0%) - SQL queries: 9 - GZIP disabled - Debug on